中英
1
width-thickness ratio中文是什么意思
发音:
- 中文翻译
- 造句
- 宽厚度
- width n. 广阔；宽度；幅度；(布匹的)门面；幅员；广博。 1 ...
- thickness n. 1.厚；粗；厚度；粗大。 2.浓度，浓厚，黏稠。 ...
- ratio n. (pl. ratios) 1.比，比率，比值；比例 ...
- blade width-thickness ratio 桨叶宽厚比
- thickness-width ratio 厚宽比
- width-to-thickness ratio 宽度与厚度的比值
- thickness ratio 板材厚度同轧辊直径之比; 厚度比
- maximum width and thickness of the pad 荚的最大宽度及厚度
- blade thickness ratio 桨叶厚度比叶厚比; 叶厚比
- diameter-to-thickness ratio 径厚比
- frequency thickness ratio 频率厚度比
- hydrofoil thickness ratio 水翼厚度比
- length-to-thickness ratio 长厚比值
- limb-thickness ratio 褶皱翼部-厚度比
- maximum blade thickness ratio 桨叶截面最大叶厚比; 最大叶厚直径比
- mean diameter-thickness ratio 平均直径与厚度比值
- radius-thickness ratio 半径与厚度比
- ratio of blade thickness to chord 叶片厚度与叶弦之比
- ratio of height to thickness 高厚比
- ratio of wall thickness to size 壁厚与管径比
- rudder thickness ratio 舵厚度比
- shroud thickness ratio 导流管厚度弦长比
- strut thickness to chord ratio 支柱剖面厚度比
- taper-in-thickness ratio 厚弦比展向变化率
- tapering thickness ratio 相对厚度沿翼展变化率
- Effects of the plates width - thickness ratios on cyclic characteristics of i - section steel beam - columns
板件宽厚比对高层钢结构压弯构件滞回性能的影响 - Since the plate is relatively wider and the width - thickness ratio of plate is always larger , the section of cold - formed steel is easy to buckle
由于冷弯型钢截面开展，各组成板件的宽厚比往往较大，截面容易凸曲。 - The chinese codes stipulate both the width - thickness ratio and the minimum thickness of the elements . that is stricter than the stipulations of north american codes
对于受压板件的壁厚，我国规范采取的是既限制板件宽厚比又限制最小板厚的规定，其限制较北美同类规范偏严。 - The national steel structure design code ( gbj17 - 88 ) is not permitted the b / t exceed ( 10 + 0 . 1 ) 235 / fy . the width - thickness ratio of the web ( b / t for short ) exceed the limitation often
钢结构设计规范( gbj17 - 88 )规定t形截面轴压构件腹板宽厚比不应超过( 10 + 0 . 1 ) ，按国家标准生产的t型钢的腹板宽厚比大多超过限值。 - In this paper , the buckling behavior of cold - formed angle members is studied by non - linear finite element method . the influence of the width - thickness ratio of the single cold - formed angle column under axial load is analysed . the criteria of flexural buckling and torsional - flexural buckling for cold - formed egual - leg under axial loads is presented . according the calculating results of the ansys finite element method , the stability - coefficient formulas are simulated for the cold - formed loading single angle members of flexural buckling and torsional - flexural buckling
本文运用非线性有限元法对冷成型单角钢的稳定性能进行了研究，分析了宽厚比对冷成型单角钢轴压杆稳定性能的影响，给出了等边冷弯角钢发生弯曲屈曲和弯扭屈曲的判断条件，根据ansys有限元的计算结果拟合出了冷成型单角钢轴压杆在发生弯曲屈曲以及在发生弯扭屈曲时的稳定系数公式，在此基础上得出了冷成型单角钢轴压杆在所有长细比情况下的稳定系数公式。 - This article analyzes the difference of theories calculating the effective width between chinese code and north american codes . the author finds the results based on the technical code for design of cold - formed thin - wall steel structure is lower than that of north american codes , especially for flat plate with relatively larger width - thickness ratio whose thickness is thinner than 2mm , the difference is more obvious
本文分析了国内外关于冷弯型钢屈曲后强度的有效宽度计算理论，通过理论分析和计算对比发现，按我国《冷弯薄壁型钢结构技术规范》计算的板件有效宽厚比值较北美规范低，特别是对于厚度小于2mm的大宽厚比板件，其差异更明显。
- 推荐英语阅读
width-thickness ratio的中文翻译，width-thickness ratio是什么意思，怎么用汉语翻译width-thickness ratio，width-thickness ratio的中文意思，width-thickness ratio的中文，width-thickness ratio in Chinese，width-thickness ratio的中文，width-thickness ratio怎么读，发音，例句，用法和解释由查查在线词典提供，版权所有违者必究。
Last modified time:Sat, 16 Aug 2025 00:29:56 GMT
关于我们
